TITAN V2 NGRS (Full Set, Front-Wired)

Drop-In MOSFET type TITAN ™ controller set transforms Tokyo Marui V2 Next Generation Recoil Shock into an advanced training replica. It Provides a tactical advantage thanks to a lightning-fast trigger reaction time with the ability modify the replica it and adapt it to every mission with the 20 help of available functions.

TITAN ™ Provides new possibilities _
- Trigger sensitivity adjustment
- Pre-cocking boost - adjustment of the time the spring That is being kept pulled (shortens the time between a squeeze of the trigger and firing)
- Adjustment of fire mode selector modes
- Burst mode
- Fire rate adjustment
- Notifies about a low battery level
- Protects battery from damage
- "sniper delay"

TITAN ™ Set Controller includes:

1. GATE ™ Control Station
Normally update the firmware and / or driver conduct adjustment from home using a USB connection and a computer application. Connect and adjust your replica using a computer or a laptop!

2. USB Connection / Plug
The USB plug operates in cooperation with GATE ™ control station and Provides a Full access to all functions offered by TITAN ™ as well as it allows perform Software updates of the control unit installed in a replica, as well as the Tactical Card Programmer. < / p>

More comprehensive description of Titan ™ controller _

TRIGGER SENSITIVITY ADJUSTMENT
Third generation proximity sensor allows controlling the trigger sensitivity. There is no need to disassemble the replica, is all that is Necessary to use The GATE ™ control station. It will allow the replica Adapting to the skills and individual preferences of the User.

Configurable FIRE MODE SELECTOR (GEN. 2)
Two sensors can be programmed in three ways one of a select 6 functions_
- SAFE-SEMI-AUTO
- SAFE-SEMI SEMI-
- SAFE-SEMI-BURST *
- SAFE-AUTO BURST *
- SAFE-SEMI-BURST * / AUTO (short squeeze-and-hold - burst, long trigger squeeze-and-hold AUTO)
- SAFE-AUTO BURST * (SAFE via a rapid mode selection, when_ SAFE-SEMI-SAFE)
* BURST Means firing a series of rounds.

CYCLE DETECTION
TITAN ™ control unit can accurately detect the position and the cycle That should end at. That is thanks, the squeeze of a trigger Causes and completion of a full firing cycle (replicas without TITAN ™ system often jam when the trigger has been squeezed for a too short of a time if it does not end with a shot. TITAN ™ eliminates this defect.).
This results in_
- Automatic Burst Mode, there is no need to set the time of the cycle of this series, the only thing is it Necessary Determine how many BBs are to be fired
- Automatic Pre-Cocking, Which is available in every mode in the fire Following mode selector settings_ SEMI and AUTO BURST. In this comparison ordinary MOSFET modules, there is no need to manually configure this setting. All that is is required to set the power of the spring pre-cocking.
- ALWAYS FULL CYCLE COMPLETED - when pre-cocking is turned off, will TITAN ™ That the ensure the gearbox will complete a full cycle and after the firing spring will be released. Thanks to this, and greater reliability of the replica is Achieved.

PRE-COCKING (Gen.2 *) < br> Winning a duel often depends on Fractions of a second, that is why it thanks pre-cocking the trigger reacts with a speed can be compared That is That of a real firearm. The spring is pulled beforehand, so at the same time, the caution That usage of this mode with the powerful springs will lead to a faster wear of internal parts of a replica.
There are two modes of PRE-COCKING function_
1. Auto - the spring is pulled after every shot
2. SMART - the spring is pulled in advance by a slow squeeze of the trigger and a shot is fired by a rapid squeeze.
Three modes of operation can programmed for PRE-COCKING: HIGH / MID / LOW - each regulates the spring sprain in different levels

* PRE-COCKING mode now operates in all fire mode selector modes_ SEMI, BURST, AUTO and does Do not require manual calibration

BURST (Gen.2)
BURST mode, i.e. firing with a pre-programmed series of rounds requires only The selection of the amount of BBs to be fired (up to 10 BBs per trigger squeeze). It is very useful in all MILSIMs or when using real / low-cap s.

ROF CONTROL
This allows it reduce the rate of fire of the replica. This allows to use more powerful Li-Po batteries and still Maintain a rate of fire compliant with Real firearms.

ROF STAB
Allows to change the way the ROF Control operates_
- ON - RoF Control regulates the cycle speed, Which allows the gearbox to operate smoothly and with a lesser wear of the replica's internal parts
- OFF - RoF control adds pauses between every shot in This order reduce the rate of fire. This Provides very realistic experience.

SNIPER DELAY
This function allows to set a delay between every shot in SEMI mode in this order delay or reload simulate recoil compensation. It is possible to set the Following delay_ 0.5 sec, 1.0 sec, 2.0 sec and 3.0 sec.

A detailed description of all functions is available on the manufacturer's website_ http // _ www.gatee.eu/

The Full manual is available at the below address _

The set includes:

- TITAN Drop-In Module
- USB plug for the control unit using the GATE Control Station app
- assembly kit
- Quick Start Guide (Angielski)